BMP project update 4 ; Ready to be painted..

After spending loonngg longg time corrections and adding details, I finally finished building the model...

First photos are from the turret..Smoke launchers and antenna pods are from Voyager, the rest from Eduard..

And now finally...The whole BMP-2 on the stage....

Everything is ready to be painted..

 

BMP-2 project update 3: The hull finished...

After lots of patience finally I finished the hull. Added / corrected many details. Instead of writing everything I want to share the photos.

Feel free to share if you have any comments..

 

 

                             

BMP-2 project: update 2

BMP-2 project continues slowly but as good as I want. I have some progres. Im spending long time to build a vehicle as correct as possible, but it worths. I hope..:)

Here are some photos. The wheels and tracks I mentioned in the introduction part, were cleaned and made ready to be assembled.

I've started detaling the model with Eduard. First I cut off the thick and bad looking fender parts and replaced with Eduard's. Then I added welding traces around back doors like in the real vehicle.

There was inaccurate kit parts which needed to be removed on the back doors of the model. I removed them and added P.E. parts.

Real vehicle back doors for comparison...

Then I've started working on upper hull. There are so many things to correct here. I started from front engine hatch. Location of the engine hatch was not correct.  I filled the wrong lines with CA, sanded and using blueprint and real photo of vehicle, I determined the correct position of the hatch.

 

Using mask band and ruler I scribed the new lines of the correct hatch.

As final P.E parts are added.. Finished engine hatch..

I've started working on maybe the worst part of the upper hull, back side..Size and position of the two hatches were wrong again. So I cut the back of the upper hull and filled with evergreen and sanding again again again..As I will add air filter and other small details from Eduard's set, I also removed them.  :)

Ready to be details with P.E

 
 Location of the hatches should be like in the photo below. After I prepare back side detailing parts, I will cement them all together considering the blueprint.

If you have ANY COMMENT or ADDITIONAL KNOWLEDGE about this vehicle, SAY IT NOW before it is TOO LATE..

BMP-2 project; episode 1: introduction...

When I had seen this vehicle for the first time, I said myself I had to build one of them. It's shape and camouflage types were really turned me on.

I made a little search about the kits of BMP-2 that I could buy. In other modelling forums it was being said that Dragon/Revell and Zvezda kits are all same molded.There was no difference. So I got this oldie Dragon model from one of my modeller friend. To be honest when I went for deeper detail of real vehicle, I realized that this kit is oldie but not goldie one. There are miss angled side skirts, misslocated hatches, size mistakes etc. I bought resin wheels and tracks from Master Club, detail set from  Eduard and gun barrel from JB model. I want to finish it as real as possible I can. I hope it worths.. :)

Here are the kit and the details parts...

I want to share some photos from detailing parts.. First wheels from masterclub..

 

Wheels are really hightly detailed but need to be cleaned..

 

Comparison of the resin wheel with the one coming from kit.. Obviously resin is much better...

As Master Club tracks are different then kit tracks, they come with its special wheels..There are 200 track links, 2 drive sprockets and 4 special spare tracks for upper hull..

 
                            

 Comparison of kit tracks and Master Club tracks.. There are even their numbers (serial numbers??) on resin tracks.

Most important benefit of these resin tracks are, they are clickable ( no need glue) and almost no need for cleaning whereas each kit tracks have pin mark which need to be cleaned..

                                             
Now Im busy with tracks and lower hull. In next episode lower hull will be finished and started to upper hull..

Keep following...

Bt-7: called it done

I finished also tracks and wheathered. Time to call this BT-7 done? :)

 

BT-7 - chipping and more wheathering

Im still busy with this BT-7. I added some chipping and more wheathering. Considering Murat Özgül's and Lars Richter's amazing winter camouflage examples, I converted lightening from green to black.

Added more washes to the egdes of the model to show its dimensions better..Note also light chipping from photos..

 

 I want to show a bit more care to grills..

Upper hull almost finished. Now its time for preparing tracks..

Bt-7 strikes back..

This sweet one was waiting its turn. This weekend instead of building kit, I wanted to paint model. For hairspray winter camo practice, I chosed my BT-7 waiting ready to paint. It is 35 scale from Tamiya.

I used Mr color and tamiya acyrilic paints for painting. Winter camo was made using hairspray technique. Wheathering not finished yet. Chipping and adding some more dirt is next step.

Black parts of the wheels looking clean compared to lower hull at the moment. I will show them my special care with tracks.. Maybe I turn lightening from green to gloss black..

Comments are welcome..If you leave any...:)

Wheels are added for photos..